Jump to content

DIY Wet Tumble Setup... add-on Giraud Tri-Way cutter?


Recommended Posts

Hi all,

 

I've decided to wet tumble my brass with stainless pins over ultrasonic or vibrating.  I was planning on buying the harbor freight dual-3lb tumbler, but decided to look at some DIY versions that were a little larger first.  

That's when I noticed a lot of people are using 1725RPM motors for their tumblers... which are also used for the Giraud tri-way cutters.  I'm thinking about combining the two into one unit... maybe just disconnect the belt from the tumbler when I'm trimming brass... maybe have a belt tensioner or something like that.  I'm thinking this could be a good way to get dual use out of a fairly expensive motor.

 

Anyone else tried this?  Any other thoughts?

Brandon

Link to comment

Well, that would work for the idea you have, but 6 lbs isn't much capacity for tumbling. Maybe enough for what you're planning on

doing.  I have a Thumlers Tumbler that has a 15 lb. capacity, but quite a bit more expensive than the Harbor Freight model.

$58 buck compared to $189.

Good luck with your project, fun thing to do.

Link to comment

I agree, 6 lbs isn't much.  That is what the Harbor Freight tumbler is.  That's why I'm looking at doing a DIY tumbler to try to get closer to 15 lbs or so.  :)

 

Pretty sure I'm going to try this... just need to save up to get the components now.  :)

Brandon

Link to comment

I've seen that one a few places.  It honestly looks like the best deal out there for commercial items.  I'm just thinking I can kill two birds with one motor if I do it this way, so it's incentive to do it... after all, money saved on reloading tools means more money for projectiles and powder, right?  :D

Brandon

Link to comment

It looks like the Giraud cutter uses a 1/8 HP motor so it should work with a reasonably sized drum.  If you decide to go with a separate motor check with your local HVAC companies, motors like this can be had for next to nothing used out of defunct heat pumps and AC units.

Link to comment

Thanks!  And great idea on the HVAC companies.  I have a few connections with a couple.  I was looking at a 1/3 HP motor, so its good to know a 1/8 HP motor would be fine with the Giraud.  With a 1/3, I may be able to even trim cases while tumbling.  Haha!

 

Brandon

Link to comment
  • 3 weeks later...

Finished the tumbler last night, and ordered the Giraud today.  :)  The motor that came out of the washer was perfect.  1725RPM, 1/2HP, shaft on both ends.  

 

I did about 150 .223 cases last night in the tumbler and it needs some tweaking, but worked great.  It's ugly, but I really don't care... I didn't build it for looks.  Haha!

 

I'll let you guys know when my Giraud gets here.  They're unfortunately back ordered until May 2nd, so I guess I'll just have to clean and size brass in the mean time.  :)

Brandon

Link to comment

Holy crap! Do they make the stand-alone cutter for .30 carbine? I wonder what they size it off of? May have to call them again next week. :) I was just looking at the one you put on your own motor.

Brandon



Cutter is universal - you just adjust the carbide blade - it will make sense once you get it. Of course if you are lazy like me you can buy extra cutters so you can set it and forget it

30 carbine has a slight taper to the cartridge, so I assume that his case holder works by not having enough taper and thus catching the car before it can drop through
Link to comment

Maybe if it looked better... lol  I was going for pure functionality on this one.   :)  I'm very happy with it and glad I didn't A) do the ultrasonic route and b: buy the tiny tumblers from Harbor Freight.   :)

 

I'm really looking forward to getting the Giraud hooked up, though.  I feel like that's the real gem in this build... if it were a news headline, perhaps it would read "Free motor pulls double duty for reloader!"  Haha!

Brandon

Edited by NeveSSL
Link to comment

Haha!  I suppose I did.  :)  Thanks.  

 

I think it's going to work out really well.  I was thinking I'd be running multiple drums, but there's really no need.  I can do at least 3 lbs of brass per run, and could do more if I had more SS pins, of which I'll order soon.  The container I have right now only has one paddle in it, so I do think I'll build another one the same size and put two paddles on.  My primer pockets aren't as clean as I think they could be, and I think more pins and another paddle will likely help that.  Don't get me wrong, they're still being cleaned for the most part, but just a tiny bit of gunk in them.  If I'm gonna do this, might as well tweak until 3 hours of tumbling equals perfectly cleaned brass.  

Brandon

Link to comment
  • 2 weeks later...

Good news... I think my Giraud trimmer is coming in today... and I fly back in tonight... WOOHOO!!!!  Should be able to attach it and trim my first cases tomorrow night.  Can't wait!

Brandon

  • Like 1
Link to comment

Edit:  I'm a dunce.  I was looking at the tumbler side of the motor... which was clockwise... which means the other end of the shaft is counterclockwise.  DOH!  This is actually working out perfectly.  :)

 

Got it setup and it works great!  Thanks for the recommendation, Hershmeister.

 

It's ugly, but it works well.  That's all I care.  :)  Ignore the tape on the powered bar... that will be changing for some pipe insulation soon.  :)

 

20160505_191821_zpsphjmfsyn.jpg

 

20160505_193719_zpsyfbcs5wb.jpg

 

20160505_193741_zpspunwi1er.jpg

 

Brandon

Edited by NeveSSL
  • Like 1
Link to comment

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

TRADING POST NOTICE

Before engaging in any transaction of goods or services on TGO, all parties involved must know and follow the local, state and Federal laws regarding those transactions.

TGO makes no claims, guarantees or assurances regarding any such transactions.

THE FINE PRINT

Tennessee Gun Owners (TNGunOwners.com) is the premier Community and Discussion Forum for gun owners, firearm enthusiasts, sportsmen and Second Amendment proponents in the state of Tennessee and surrounding region.

TNGunOwners.com (TGO) is a presentation of Enthusiast Productions. The TGO state flag logo and the TGO tri-hole "icon" logo are trademarks of Tennessee Gun Owners. The TGO logos and all content presented on this site may not be reproduced in any form without express written permission. The opinions expressed on TGO are those of their authors and do not necessarily reflect those of the site's owners or staff.

TNGunOwners.com (TGO) is not a lobbying organization and has no affiliation with any lobbying organizations.  Beware of scammers using the Tennessee Gun Owners name, purporting to be Pro-2A lobbying organizations!

×
×
  • Create New...

Important Information

By using this site, you agree to the following.
Terms of Use | Privacy Policy | Guidelines
 
We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.