Jump to content
DWARREN123

Glock 48

Recommended Posts

Picked up one about a month ago and like it.

Had Truglo H3 sights put on it.

It had a 7 to 7.5 pound trigger and the rough Glock trigger face.

Well this is the first Glock I have decided to mod.

I used fine wet/dry paper to smooth the trigger face and make the trigger safety lever even with the trigger when the trigger is pulled.

I polished the metal internals with 500/1000/2000 grit polish compound and polishing wheell .

The polishing dropped the trigger pull down about a pound due to removing some very rough edges. You will get rough edges on stamped metal.

I then replaced the striker spring with a Ghost INC. 4.5 pound spring and the safety plunger spring with a Ghost INC. reduced power spring. This reduce the pull down to 4.5 pounds. This is the best and cheapest way to reduce the trigger pull.

All this cost me $10.23 for the Ghost springs and has given me a good trigger and is much easier for me to shoot accurately.

I have shot the pistol after each mod to see what improved and what needs more improvement. I have gotten to the point where I am very happy with this pistol for carry.

I now have about 1,450 rounds thru it.

  • Like 1

Share this post


Link to post
Share on other sites

All I've done to mine is change the sights.  I love Glock plastic sights...because they are so easy to remove lol.  I'll polish the internals sooner or later, but I doubt I'll mess with springs on a carry gun.  

I was irritated that Comp-Tac wouldn't make a CTAC for the 48 and I told them more than once.  One day, I realized that they make a 43 CTAC.  I bought one and put the Dremel to work.  Now I have the best carry gun I've ever bought with the best IWB holster made 😀

Edited by deerslayer
  • Like 1

Share this post


Link to post
Share on other sites

Just a FYI. Ghost inc. has dropped the prices on the reduced firing pin springs and reduced power safety plunger springs so with shipping they are under $9.00.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Content

    • By ken_mays
      I've got about 350 rounds downrange with the Masada as of today.  
      Basics:
      2 x 17 round magazines, with remarkably stiff springs. Comes with 2 backstraps (small and large), and optic mounting kit with 4 RDS-specific spacer plates and appropriate screws.   The optic cut cover and all the mounting plates are plastic. The RDS plates included are for: Deltapoint, RMR, Venom, and Romeo 1. Trigger pull is 4 lbs, about 4.5mm worth of takeup and another 4mm of smooth, non-stacking creep. Ambi mag release and ambi slide release. Steel 3-dot sights. Handling and shooting impressions:
      Good hand feel for me, I left the large backstrap installed. Trigger has a great pull, but trigger slap does occur on mine.   Out of the box, shooting a few mags of mildly hot 9mm earns you a stinging trigger finger.    After mounting a RDS, the trigger slap was softened and all but unnoticeable.  The Glock-type safety dingus isn't really a problem.  I'd put about 100 rounds through it before I installed the Vortex Venom RDS, and the trigger slap was unpleasant enough that I was considering getting rid of the gun.  After installing the RDS and putting 250 more rounds through it with considerably tamed trigger slap, I feel like it was built and intended for RDS use exclusively. Sights are very much a "combat hold" setup, where the POI is about where the white dot on the front sight is.   I was using a 6'oclock hold at about 10 yards and my group was about 1.5"-2" below the 1" dot that I was resting atop my front sight. Accuracy was about average for your typical $400 polymer combat pistol, about on par with my S&W M&P 1.0s, at least while shooting irons. The rear sight notch is a bit too wide for me, so that likely contributed.  With the RDS, accuracy seemed to tighten up to the point I had no complaints. Reloads were not as fast as I'd have liked.   The front of the magazine extends up into a "tab" that is prone to catch on the frontstrap side of the mag opening.  The mag opening has a pretty good bevel on the rear but not on the sides or front, which are thin; and the recessed area on both sides doesn't do you any favors, either.  The mag release button is a bit small and requires me to twist the gun just a bit to hit it reliably, but since this is an ambi mag button, I may just work on hitting it with my trigger finger instead.  At least the mags eject briskly. Slide release is large and easy to hit but not big enough to be in the way. The gun doesn't seem all that fat, but the only holster it would fit in is the one for my Steyr M9, which, along with the Beretta APX, has the fattest slide of any gun I own.  Fortunately, the Steyr, APX, and Masada all fit very nicely into the same holster, so that what I'll use. Reliability was 100% with my ammo, which are 115 gr coated lead reloads running about 1200 FPS. Summary:
      An exceptional value at a little over $400.   Trigger slap is something to watch out for, maybe it was just my gun, but installing a RDS made that a non-issue.  Due to its magwell, mag changes are a little slow.  Accuracy and reliability earn an "A" for me.  Sights adequate but not optimal.
       
       
       


    • By owejia
      Thinking about getting a 9mm revolver. Needs to be ss, short barrel. what is a good buy? Taurus model 905 ss 2", or the Ruger sp101 ss 2.25, Charter arms Pitbull ss or there other short barrel 9mm revolver out there? Opinions, likes and dislikes. What say you?
    • By Swang
      Seems like 2020 may be the year of the RMR. Seeing a lot of new guns pre-milled. Never been a RMR guy but this may create an interest now that I won’t need to get it milled and recoated. Just curious if RMRs are all standardized hole patterns and footprints though...

The Fine Print

Tennessee Gun Owners (TNGunOwners.com) is the premier Community and Discussion Forum for gun owners, firearm enthusiasts, sportsmen and Second Amendment proponents in the state of Tennessee and surrounding region.

TNGunOwners.com (TGO) is a presentation of Enthusiast Productions. The TGO state flag logo and the TGO tri-hole "icon" logo are trademarks of Tennessee Gun Owners. The TGO logos and all content presented on this site may not be reproduced in any form without express written permission. The opinions expressed on TGO are those of their authors and do not necessarily reflect those of the site's owners or staff.

Before engaging in any transaction of goods or services on TGO, all parties involved must know and follow the local, state and Federal laws regarding those transactions. TGO makes no claims, guarantees or assurances regarding any such transactions.

×
×
  • Create New...

Important Information

By using this site, you agree to the following.
Terms of Use | Privacy Policy | Guidelines