Jump to content

1975 Winchester 94 Project


Spots

Recommended Posts

Just picked this one up off armslist tonight. Gonna make it into a nice brush gun hopefully. The stock has a 6" crack running forward from the butt plate and the bluing is starting to pop like most of the post 64 models. Plans are to either pin and refinish the stock along with the forearm or buy new and fit as necessary. Cerakote in Socom blue or whatever gets me the closest look to bluing from 5' since these models do not take bluing well. Add a Williams FP peep sight and a brass front blade. Shoot and enjoy. 

20211121_205937.jpg

Screenshot_20211120-221232_Samsung Internet.jpg

20211121_205921.jpg

20211121_205947.jpg

Edited by Spots
Added pics
  • Like 6
Link to comment
5 minutes ago, Handsome Rob said:

Man, I own a 1974 model that could be that things twin. Bluing freckles & all.

Watching with interest. 

This will be the first gun Ive done in a long time. And the first one where I actually have enough disposable income to be able to do it right and not cut every corner. 

  • Like 1
Link to comment

Stripping it down. This is the stock crack. Im very tempted to attempt to fix it and refinish just to see if I can make it look right. As was mentioned earlier if i screw it up I can buy a new stock for under $10020211122_135156.thumb.jpg.f1338a14e8f02723fdcd1764dfd8d147.jpg20211122_135205.thumb.jpg.9707ac5ba5d7ea0dab7d708f39c1cef0.jpg20211122_135216.thumb.jpg.68ecfaf8d47920c094c3c7caa48d822c.jpg

Link to comment
33 minutes ago, Spots said:

Stripping it down. This is the stock crack. Im very tempted to attempt to fix it and refinish just to see if I can make it look right. As was mentioned earlier if i screw it up I can buy a new stock for under $10020211122_135156.thumb.jpg.f1338a14e8f02723fdcd1764dfd8d147.jpg20211122_135205.thumb.jpg.9707ac5ba5d7ea0dab7d708f39c1cef0.jpg20211122_135216.thumb.jpg.68ecfaf8d47920c094c3c7caa48d822c.jpg

That's what I would do!!!

Link to comment
1 hour ago, Spots said:

Stripping it down. This is the stock crack. Im very tempted to attempt to fix it and refinish just to see if I can make it look right. As was mentioned earlier if i screw it up I can buy a new stock for under $10020211122_135156.thumb.jpg.f1338a14e8f02723fdcd1764dfd8d147.jpg20211122_135205.thumb.jpg.9707ac5ba5d7ea0dab7d708f39c1cef0.jpg20211122_135216.thumb.jpg.68ecfaf8d47920c094c3c7caa48d822c.jpg

I Revlon some super, super thin CA glue dribbled in there, then bound tight for a few days will make that disappear entirely. 

  • Like 1
Link to comment
5 hours ago, Spots said:

Stripping it down. This is the stock crack. Im very tempted to attempt to fix it and refinish just to see if I can make it look right. As was mentioned earlier if i screw it up I can buy a new stock for under $10020211122_135156.thumb.jpg.f1338a14e8f02723fdcd1764dfd8d147.jpg20211122_135205.thumb.jpg.9707ac5ba5d7ea0dab7d708f39c1cef0.jpg20211122_135216.thumb.jpg.68ecfaf8d47920c094c3c7caa48d822c.jpg

Brownells did a utube vid on how to repair that. have to steam all of the oil and stain out before you epoxy it. I'll try to find it and post a link.

Link to comment

 Another thing you might want to look at is the cartridge lifter. Those old cast steel 94's typically came with a over hardened stamped lifter that had a habit of cracking. Winchester made thousands of replacements in a nice cast steel. The stampings were blued while the cast replacements were in the white. Good Luck with the project!

  • Like 1
Link to comment
3 minutes ago, xtriggerman said:

 Another thing you might want to look at is the cartridge lifter. Those old cast steel 94's typically came with a over hardened stamped lifter that had a habit of cracking. Winchester made thousands of replacements in a nice cast steel. The stampings were blued while the cast replacements were in the white. Good Luck with the project!

As long as its not cracked am I good? Or should i replace it while Im in there anyways

Link to comment

Brought the stock into work with me today. Filled the cracked using the screw hole as an entry port, and pumped the entire hole and crack full of Acralock. We use this stuff to install boat decks onto hulls. 2750 psi working strength, 80-120% elongation before it sheers after curing. Its some heavy duty ####. I got it taped and zip tied up tight while that cures. Full cure is 1.5 hours so at lunch im gonna pull it down and drill it and dowel it with 1/4" diameter aluminum rods in a couple spots, again installed using acralock. My goal isnt an invisible repair, its a clean and neat repair with as much strength as possible. 

20211123_081451.jpg

20211123_082905.jpg

  • Like 2
Link to comment
22 minutes ago, Spots said:

Brought the stock into work with me today. Filled the cracked using the screw hole as an entry port, and pumped the entire hole and crack full of Acralock. We use this stuff to install boat decks onto hulls. 2750 psi working strength, 80-120% elongation before it sheers after curing. Its some heavy duty ####. I got it taped and zip tied up tight while that cures. Full cure is 1.5 hours so at lunch im gonna pull it down and drill it and dowel it with 1/4" diameter aluminum rods in a couple spots, again installed using acralock. My goal isnt an invisible repair, its a clean and neat repair with as much strength as possible. 

20211123_081451.jpg

20211123_082905.jpg

If you sink the rods a bit, you could plug the hole with a wood plug stained to closely match.

  • Like 1
Link to comment

So this is where Im at now. The cracked is sealed completely with acralock. I drilled a blind hole through the bottom and seated a 1/4" rod about 4" long into the stock and acralocked into place. I decided to just leave the black dot. I can always use wood filler later to help blend it. The stock is hand sanded to 220. The pictures are with it whipped down with a damp rag. Thats the final color im after. Next comes hand sanding to 600 grit then a truoil finish.  Then the forearm will get the same treatment. Im happy with it. Total repair cost to date $0

20211123_172935.jpg

20211123_172944.jpg

20211123_172950.jpg

  • Like 6
Link to comment

So decided since this rifle has been free so far I would try something different before I decide to cerakote the rifle. The epoxy in the stock cured tight so I hand sanded the stock and forearm down to 800 grit. Then I used a method I found online of putting on tru oil and mixing it with Armor all. It has a catalyst effect on the tru oil causing it to cure faster and harder. I was able to hand rub a dozen coats of tru oil into the stock and forearm. I then went after the receiver. I wet sanded it down to 1k grit, then using a technique I used on knives, I did a mustard and vinegar steam patina in the receiver. The result is a gray, antique worn look. It looks much better than the rusty freckles tat where on it. For now Im gonna call this one good enough for the deer woods. 

20211124_234859.jpg

20211124_234848.jpg

20211124_222142.jpg

20211124_222154.jpg

20211124_232425.jpg

20211124_232432.jpg

20211124_234839.jpg

20211124_234831.jpg

20211124_234818.jpg

  • Like 2
Link to comment
50 minutes ago, hipower said:

Looks great, I think. Have you plans to do the forend like the rear? Yeah, I'm a nit-picker. lol It would truly look fantastic.

Yes, eventually. I wanted to get an idea of how it was gonna look together before i stripped and patinaed the rest of it. Also wanna see how maintenance intensive it is first. It may end up cerakoted in the end but Im digging the look.

  • Like 1
Link to comment
  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

TRADING POST NOTICE

Before engaging in any transaction of goods or services on TGO, all parties involved must know and follow the local, state and Federal laws regarding those transactions.

TGO makes no claims, guarantees or assurances regarding any such transactions.

THE FINE PRINT

Tennessee Gun Owners (TNGunOwners.com) is the premier Community and Discussion Forum for gun owners, firearm enthusiasts, sportsmen and Second Amendment proponents in the state of Tennessee and surrounding region.

TNGunOwners.com (TGO) is a presentation of Enthusiast Productions. The TGO state flag logo and the TGO tri-hole "icon" logo are trademarks of Tennessee Gun Owners. The TGO logos and all content presented on this site may not be reproduced in any form without express written permission. The opinions expressed on TGO are those of their authors and do not necessarily reflect those of the site's owners or staff.

TNGunOwners.com (TGO) is not a lobbying organization and has no affiliation with any lobbying organizations.  Beware of scammers using the Tennessee Gun Owners name, purporting to be Pro-2A lobbying organizations!

×
×
  • Create New...

Important Information

By using this site, you agree to the following.
Terms of Use | Privacy Policy | Guidelines
 
We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.