Jump to content

Recommended Posts

I have a question for the AR experts. First off I'm an AK guy, its simple, rugged and reliable. I have ventured into the AR realm and have run into something troubling that I can't figure out. I took in an AR in trade, Aero Precision, and it cycled by hand, unloaded just fine. Nice buffer tension, snappy detents and the bolt went home with a satisfying thunk. I loaded up a magazine, inserted , pulled the charging handle, released and....... the carrier would not go into battery. I pushed the forward assist and it went in with some effort. I decided to check it. The issue arose when I tried to eject the live round by hand. It was stuck. I had to remove the upper and pry the bolt carrier to the rear. It was jammed in good. The bolt lugs would not rotate unless I physically pried the carrier back...it ejected out on its own. I almost took a rubber mallet to the charging handle to get the carrier to move, that's how stuck it was. 

The rifle is pristine, no fouling or wear marks, that's the reason I accepted it in trade. Is it a headspace issue? Does it need a break in period? I have not fired it because of the forward assist being used on the first fed round. I know is sounds silly but I'm paranoid with any weapon that I'm not familiar with. Any help would be greatly appreciated.

Link to comment

I loaded up a mag with factory steel rounds, Wolf to be exact, and the bolt carrier slammed home no problem. Yes I was using handloads made just for this rifle, just didn't realize how finicky it could be. I've ordered some virgin brass cases and will fire form them to this rifle. My once fired brass will have to be gone through and rechecked to insure it is in spec and my loaded rounds will be pulled and reprocessed. My only waste is time and worry at this point. It's for damn sure not an AK.

Thank you, gentlemen,  very much for the information and guidance. 

  • Like 1
Link to comment
12 hours ago, Alleycat72 said:

If you get a small base die, you'll never have that problem again. Some chambers need it and some don't. 

I will look and see what Lee has. Don't want to have this again! I will pull the 100 rounds that I loaded and see if there is a pattern by headstamp. I have loaded up 3 types of factory rounds and not one issue. I feel like a noob but better embarrassed than fingerless.  I really appreciate the replies.

Link to comment
13 hours ago, Alleycat72 said:

If you get a small base die, you'll never have that problem again. Some chambers need it and some don't. 

I guess I’ve been lucky as I’ve never used or felt the need to use a small base die.

I can’t help but believe that a properly made sizing die should size a case back to SAAMI specs if adjusted properly. This should then work in a properly chambered firearm, just like factory ammo should.

14 hours ago, ArmyBrat61 said:

I loaded up a mag with factory steel rounds, Wolf to be exact, and the bolt carrier slammed home no problem. Yes I was using handloads made just for this rifle, just didn't realize how finicky it could be. I've ordered some virgin brass cases and will fire form them to this rifle. My once fired brass will have to be gone through and rechecked to insure it is in spec and my loaded rounds will be pulled and reprocessed. My only waste is time and worry at this point. It's for damn sure not an AK.

Thank you, gentlemen,  very much for the information and guidance. 

An AR is a battle rifle, designed for battle conditions, and is in no way “finicky”. I doubt seriously your AK would chamber an out of spec round either.

I not sure how many ARs are laying around here, probably 8 or 10, and I assure you any of them will chamber, fire, and eject any in spec 223 or 556 round that’ll fit in a magazine.

Perhaps your particular rifle has a really tight chamber, or perhaps you need to screw your sizing die into the press further.

You’d really need to do some measuring to know for sure.

Link to comment
33 minutes ago, gregintenn said:

I guess I’ve been lucky as I’ve never used or felt the need to use a small base die.

I can’t help but believe that a properly made sizing die should size a case back to SAAMI specs if adjusted properly. This should then work in a properly chambered firearm, just like factory ammo should.

An AR is a battle rifle, designed for battle conditions, and is in no way “finicky”. I doubt seriously your AK would chamber an out of spec round either.

I not sure how many ARs are laying around here, probably 8 or 10, and I assure you any of them will chamber, fire, and eject any in spec 223 or 556 round that’ll fit in a magazine.

Perhaps your particular rifle has a really tight chamber, or perhaps you need to screw your sizing die into the press further.

You’d really need to do some measuring to know for sure.

Most of the problems come from progressive presses. This assumes everything is set up properly in the first place. I've had normal dies that work just fine on a single stage, but if used on my Dillon the brass is a bit tight in some guns. It's from the inability to cam over like you can with a single stage. I use the Dillon when I am processing brass for my ar10 or ar15. The trim die is essentially a small base die. Everyone will drop freely from a case gauge after loaded. I can't have a problem 12 hours from the house. I've seen what happens when ammo on the large end of the spec meets a chamber on the small end of the spec. Thankfully I always take twice as much ammo as I think I'll need and have had to donate some to the cause.  @Handsome RobI usually do 1k 5.56 or 308 at a time and you can definitely feel the difference in some chambers from the change in force needed to size them.

  • Like 2
Link to comment
1 hour ago, Alleycat72 said:

Most of the problems come from progressive presses. This assumes everything is set up properly in the first place. I've had normal dies that work just fine on a single stage, but if used on my Dillon the brass is a bit tight in some guns. It's from the inability to cam over like you can with a single stage. I use the Dillon when I am processing brass for my ar10 or ar15. The trim die is essentially a small base die. Everyone will drop freely from a case gauge after loaded. I can't have a problem 12 hours from the house. I've seen what happens when ammo on the large end of the spec meets a chamber on the small end of the spec. Thankfully I always take twice as much ammo as I think I'll need and have had to donate some to the cause.  @Handsome RobI usually do 1k 5.56 or 308 at a time and you can definitely feel the difference in some chambers from the change in force needed to size them.

Now that makes perfect sense. I’ve never used a progressive press.

Link to comment
  • 3 weeks later...

Hey, I dont know if you've resolved your issue, but I had a similar issue with mine awhile back. My issue was two fold, one my buffer tube was commercial spec and not milspec, after doing that swap I didnt have any issues for about 60 rds, then it locked up, and the only way I could free it was to "mortar" it. If you dont know what means, its where you slam the buttstock onto a hard surface, this usually gets the bolt carrier to go forward, and then you can retract the bolt, anyways, after those 60 rounds, I noticed my actual buffer had a chip on it and was catching in the tube slightly, I replaced the buffer, and havent had an issue since, I've run over 1k rounds through her since then.

Link to comment

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

TRADING POST NOTICE

Before engaging in any transaction of goods or services on TGO, all parties involved must know and follow the local, state and Federal laws regarding those transactions.

TGO makes no claims, guarantees or assurances regarding any such transactions.

THE FINE PRINT

Tennessee Gun Owners (TNGunOwners.com) is the premier Community and Discussion Forum for gun owners, firearm enthusiasts, sportsmen and Second Amendment proponents in the state of Tennessee and surrounding region.

TNGunOwners.com (TGO) is a presentation of Enthusiast Productions. The TGO state flag logo and the TGO tri-hole "icon" logo are trademarks of Tennessee Gun Owners. The TGO logos and all content presented on this site may not be reproduced in any form without express written permission. The opinions expressed on TGO are those of their authors and do not necessarily reflect those of the site's owners or staff.

TNGunOwners.com (TGO) is not a lobbying organization and has no affiliation with any lobbying organizations.  Beware of scammers using the Tennessee Gun Owners name, purporting to be Pro-2A lobbying organizations!

×
×
  • Create New...

Important Information

By using this site, you agree to the following.
Terms of Use | Privacy Policy | Guidelines
 
We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.