Jump to content

Opinions on Hornady Lock-N-Load AP


Recommended Posts

So I currently have a Lee single stage press for decapping and resizing rifle(.223 & 300BLK). And I have a Lee Loadmaster I have done a ton of work to getting it to run right that I use to assemble rifle, and do 9mm. It has a Hornady powder drop that I love. But it just has too many small issues that drives me nuts. Sooooo, I'm thinking about buying a new press. I do not want a Dillon. Yes, they are premo. But they are also expensive. Tool heads for them are also expensive. I don't want to invest that much into a press. This Hornady lock-n-load is calling my name. I like the die bushing setup instead of a turret plate. I like the spring case retainer design. I like how it indexes. Not crazy about the 100 count primer tube, but I'm a machinist, so I'll modify it to accept more I'm sure. Anybody own one? Likes? Dislikes?

Link to comment

I have one and it works as expected.  As with any machine, it may take a bit of adjusting, but once adjusted, it turns out the rounds.   I have the case feeder as well.   I have used the Dillons as well and they are good.  I think once you get used to either one, they both do the job well.

Link to comment

I've got the LNL and love it......

 

To be honest,  I don't  use the bushing setup ....I end up running 500-1500 rounds of one ammo (over a couple of weeks) then change to another caliber...When I switch back I screw the dies down to the locking rings and then adjust.......I don't find resetting the dies that much trouble......I guess if I changed calibers a lot it might become a pain...

 

Primer Tubes can be a pain, but I picked up a couple of spares....I fill them and the primer tube on the press and I'm ready for 300 rds.....about what I will feel like doing in a sitting......I tried the  Frankford Arsenal Vibra-Prime Automatic Primer Tube Filler and had mixed results....The first one I got working after some tweaking, but the motor died within a week....Midway replaced it and I haven't had a chance to tweak the new one to get it to work.........

 

I just added the case feeder and am loving that option (Christmas present to self)......One less 'movement' when loading....Don't think I'll ever add the bullet feeder though...I like the interaction of inserting the bullets and I feel like I'm having just the right amount of interaction with the load....The case feeder also took one thing 'off my plate' every time I pull the handle.....

 

One thing I did invest in is the RCBS Lockout Die.....It's a 'powder check' and when set correctly won't let the press cycle if you've double charged or missed a charge (which can happen if you're tweaking timing or having minor issues)....It's a little finicky at first, but a nice thing to have......

 

The Dillon stuff is good, but like you said you'll pay a premium unless you can find one used....(and still they may be at a premium)......

Link to comment
I also ordered shellplates and extra bushings. Since I already have a Hornady powder drop, I plan on setting it up for pistol, 9mm specifically. 9mm will be a drop in setup, with no adjustments needed. The powder drop coming with the press will be for small rifle. And I should have enough bushings for my rifle dies to make swapping calibers a very small task.
Link to comment

I think you'll like it. I acquired a used LnL last summer through an ad on TGO & have used it for .38/.357 & .45 so far. It's my first press, so I don't have comparisons to offer. 

I like it, and I like the bushings because I like to change calibers. Get some spare retainer springs for your shell plates..sometimes they get crushed in the process. They're available  in a 3 pack.

  • Like 1
Link to comment

Hi Bill Morgan on youtube( the LNL specialist) has setup the LNL and discusses the various problems that occur.He is very through and extremely talented and explains every thing and any thing about LNL

 

Here is a in depth 5 part series on setting the press up and tips and tricks.He is very enjoyable to watch.Bill even has a series on a Dillion Square Deal and now he is doing a Redding series

 

http://youtu.be/-qC1O5FzSCA?list=PL3gouk-e0H8HX-PN_XXgjMDfKnpUUmZ4H

 

Like already stated every press has its quirks Hope this helps

Edited by wolverine
  • Like 1
Link to comment

I've watched a couple of his videos, which is like an hour and a halves worth. I like his honesty. "oops, I just made a mistake. I can't believe you guys are watching my videos". I have followed his advice and deburred my press as well as machining a custom "washer" to hopefully eliminate some common shellplate issues. I am working on a case feeder for it now.

Link to comment
  • 2 weeks later...

i didn't get the bullet feeder, but I did get the bullet feed die and the tube, I will say don't waste your money on it. I would get about a 50% bullet drop out of it. The other 50% I would just put it in there manually, so I finally just did away with it and moved the seater die there and went back to a lee factory crimp in the last station. The case feeder has some issues as well, such as cases sometimes get behind the plate and knock it off the spindle. I am going to drill and thread the shaft so I can put a bolt on it to keep it down. I do like the case feeder when it works though. Seems like Hornady would have done something to lock the plates down though.

  • Like 1
Link to comment

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

TRADING POST NOTICE

Before engaging in any transaction of goods or services on TGO, all parties involved must know and follow the local, state and Federal laws regarding those transactions.

TGO makes no claims, guarantees or assurances regarding any such transactions.

THE FINE PRINT

Tennessee Gun Owners (TNGunOwners.com) is the premier Community and Discussion Forum for gun owners, firearm enthusiasts, sportsmen and Second Amendment proponents in the state of Tennessee and surrounding region.

TNGunOwners.com (TGO) is a presentation of Enthusiast Productions. The TGO state flag logo and the TGO tri-hole "icon" logo are trademarks of Tennessee Gun Owners. The TGO logos and all content presented on this site may not be reproduced in any form without express written permission. The opinions expressed on TGO are those of their authors and do not necessarily reflect those of the site's owners or staff.

TNGunOwners.com (TGO) is not a lobbying organization and has no affiliation with any lobbying organizations.  Beware of scammers using the Tennessee Gun Owners name, purporting to be Pro-2A lobbying organizations!

×
×
  • Create New...

Important Information

By using this site, you agree to the following.
Terms of Use | Privacy Policy | Guidelines
 
We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.