BeMan
-
Posts
40 -
Joined
-
Feedback
100%
Content Type
Forums
Events
Store
Articles
Posts posted by BeMan
-
-
-
Another fan of AA#9. Works best in .44 mag rifles, but fine in 6 inch and better revolver barrels.
-
Stumpy mentioned some good options. I have 3 to add to the list. Out Back Gun Parts 812-945-0480 (Tues-Friday). Michael Watson, 2449 Avenida Mastil, San Clemente, CA 92673 ( He sells some parts on ebay under username "Lightfoot"). Ken Bean 717-755-9070. Hope this helps.
-
I finally got a pound at Fox and Company, when they received an order of 4# of it. I called around everywhere I could think of and and Fox and Co. wrote my name and number down, then called when their order arrived. Good service! I will remember that when I need more supplies.
-
H&H didn't have the Varget. Says he has been out for a while. The search goes on.
-
Hey thanks. I will visit H&H this week.
-
Anyone in East TN have a pound or so of Varget to sell?
-
I went to "Cast Boolits" web site and ordered 50 cast bullets that were cast from a Lyman mold. Hollow base and 500 gr., it should work well.
-
Has anyone seen any .58 caliber ML bullets anywhere? They seem to be more difficult to find.
-
Just now getting back to this topic after having found the needed info. The authoritative book on the subject is, "Loading Cartridges for the Original 45/70 Springfield", by J.S. and Pat Wolfe. Buffalo Arms carries the book and that is where I bought the 500 gr bullets of the 20:1 lead/tin ratio. You will enjoy the book. Good luck.
-
You have an earlier trapdoor. It has the early rear sight. After 1880, trapdoors were issued with the "Buffington" sight that was graduated to 1400 yds. Your sight at it's lowest setting was zeroed for about 200 yds if I remember correctly (what was considered battle distance). You may have decent accuracy with the Goex loads or Ten-X brand. A good source for products such as ammo for these old rifles is "Buffalo Arms Co."
-
Had one of these when I lived in WY. I paid $800 for it and shot it about 50-60 times. Factory ammo is woefully inaccurate in these. The loads MUST be matching the original loads for the trapdoor. I bought a book that told me the load recipe. With that load, it was dead on with the Buffington sight that adorned it. I had to pay a guy to load the rounds for me and it became cost prohibitive, so I sold it back to the guy I bought it from. He was hitting metal sillouites at 800 yds with it. The loads were 70 gr black powder (compressed loads) using a 500 gr lead bullet that is 20:1 lead to tin ratio. Hope this helps.
-
johnnyfox,
Uhmm, now you have me thinkin. How many of us would want to add a good .22 LR rifle to the mix?
As for the pistols, the Glock would have my vote. Although I have a G27, I have a 9mm conversion barrel due to the fact that 9mm ammo is everywhere and 9mm would probably get the nod as most available "SHTF" ammo. So, what would everyone choose as a .22 ?
-
Boise, Idaho! Really? Anyways, you may want to try heating the receivier, then penetrating oil soak for at least 20 min. Use a synthetic mallet to tap the barrel near the receiver a few times with moderate force to allow the metal to vibrate. Repeat the operation if needed, but a couple of times usually will do the trick. See if this helps. If you do not have a hot air gun for heating, submersion in boiling water for 5 minutes may work.
-
Anyone in the Knox area have any .50 cal ammo cans for sale?
-
I bought a Vortex Crossfire low power varible, and it seems like a good product so far. I have read good things about the Sparc as well. There are several good choices, and many have been mentioned here. Base on what you are looking for, I would go with Primary Arms or Vortex.
-
I have used Johnsons Paste Wax for years. Inexpensive and it is basically Carnuba wax, and not a petroleum based product. For more serious protection and improved appearance I use boiled linseed oil, which can be found in about any hardware store.
I use Birchwood Casey Stock Sheen and Conditioner. The stuff works great and has some mild abrasives in it. I have even used it to remove marker, pen and crayon marks on the wood furniture by the little ones. They make an entire line for stocks which most professionals use. -
I saw a revolver with ties to 9/11 on Auction Arms. The item # 10541071
-
And we think that the price of gold has gone up..........! All in all, prices were laughable.
-
I plan on being there Sunday. Bringin my P226. Maybe trade if I can find something that interests me.
-
In East TN, my favorites are: Sevier Indoor Range (Sevierville), and Rocky Top Armory (Seymour). Both are great places to look and trade.
-
I have one in 45LC and it has been a great gun. I had one in .357, and as someone else mentioned, had trouble with it feeding .38 spec loads.
-
Does this mean that I can't bring boxed ammo in to sell if I want to? How will I recognize you guys? You rent tables?
Tony
-
Anyone here plan on going to the gunshow this weekend?
Hornady Superformance SST Ammunition 270 Winchester 130 Grain
in Ammunition and Reloading
Posted
I have a Kimber Classic in .270 that only likes Federal premium (Nosler ballistic tip) 130 gr. Win. PP next best. My 6.5 Creedmoor does not shoot the Hornady ammo well and I have yet to read of anyone who has had great success with the Hornady ammo.