Leaderboard

Ruger single six Old model 3 screw NOT CONVERTED 22LR 5.5” barrel . Great shooter! In process of buying another stainless single six , so wanting to move this one . SOLD

Dust cover comps aren’t very effective as such. You tend to get more benefit from the weight near the muzzle. They can also complicate holster selection.

1944 SAGINAW "S.G." M1 Carbine (M1 Carbine). Most parts marked "SG" (See Photo Link). Includes (2) magazines, a reproduction sling, oiler, and mag pouch. Pick up at my location $1650 CASH (No Trades Please) Shipping is FFL to FFL $45 PHOTO Link: https://imgur.com/a/k13KKCa Thanks for looking!

Good 90cc+ saw. Maxflow air filter setup, a new meteor piston, and new bearings and seals. Full wrap handle with the wide west coast style clutch cover and big west coast dogs. 34” Oregon light bar with full chisel chain. Bar tail slot has been lengthened for an experiment on another saw but works fine on this one and doesn’t loosen up or anything. Just wanted to be transparent. 7 tooth sprocket. The light weight bar keeps it from being so nose heavy and saw runs like a top with plenty of power even with the bar buried. $850 obo meet up near Oliver Springs. If you want to meet here you can test cut in a piece of wood. Will post video of it cutting tomorrow 7/12. Only trade I would consider would be a Colt Detective Special with exposed ejector rod with or without cash or an LTT beretta bobcat. May also consider semi automatic 12 gauge shotguns, can add cash for the right deal.

Let me start off with saying if you feel unable or unwilling to do the following care instructions then these aren't for you. Care Instructions 1. Keep your knife clean after each use. 2. You can wash your knife with soapy water. 3. Immediately dry off the knife. 4. Apply mineral oil or vegetable oil after use for long lasting results. 5. NEVER PUT YOUR KNIFE IN THE DISHWASHER!!! Made from 1/8" thick D-2 steel. Rockwell hardness is 58-60. They have camel bone and G10 handles. I'm not providing a block with these as one of the magnetic style blocks would be best. Your home and style and price range depends on what block you'd like. The magnetic blocks are all over Amazon, Ebay and o places. Price is $225 shipped for the set. I will only sell as a set.

They were also in their teens/early 20’s, lol.

I have a Limbsaver pad somewhere that I wear when I’m going to be shooting hard kicking rifles. It comes in very handy during the summer when I’m wearing just a T shirt and sighting in a 45-70.

New in the box. Comes with 2 30 round mags. Have box and everything it came with $1100 Must be legal to own in TN. Not interested in trades. Located and pickup in Murfreesboro. Venmo or cash as payment. Pretty flexible on time. Text 615-542-3513

I HAVE A LIKE NEW SIG SAUER P227 W/RAIL 4" BARREL, 10 RD 45 ACP, 3 10RD MAGS, NIGHT SIGHTS, CASE. MADE IN 2018. MAYBE 80RDS FIRED AND HAS BEEN A SAFE QUEEN. $875 OBO NO TRADES, REDUCING SAFE QUEEN INVENTORY. MEET IN MIDDLE TN ALONG I24. BUYER MUST BE LEGALTO OWN A PISTOL AND HAVE TN DRIVERS LICENSE AND/OR TN HCP (PREFERRED) MESSAGE ME IF INTERESTED.

I have what I believe to be is an unfired, LNIB Winchester 1886 Extra Light in 45-70 for sale. Made in Miroku, Japan. Includes a brand new and uninstalled Lyman receiver sight. This thing is absolutely beautiful. They don’t make this model anymore. $1300 cash FTF around Columbia to a Tennessee resident over 21 years old who is legally eligible to own firearms. HCP preferred. Not really looking for any specific trades but you never know. Could always use a Trijicon RMR HD.

Finally finished up my 300BO pistol build. I really love how it turned out.

I HAVE LIKE NEW RUGER SS SINGLE 10 LR WITH 5.5" BARREL AND WALNUT GRIPS, FIBER OPTIC FRONT/REAR SIGHTS, CASE, ETC. MAYBE 50 RDS FIRED. MADE IN 2011. HAS BEEN A SAFFE QUEEN AND REDUCING INVENTORY. $650 BUYER MUST HAVE TN LICENSE AND/OR TN HCP. MEET CLOSE TO MANCHESTER OR MCMINNVILLE TN. MESSAGE ME IF INTERESTED.

I HAVE LIKE NEW SS RUGER NM BLACKHAWK 357 MAG WITH 4 5/8" BARREL AND WALNUT GRIPS. NO CASE. LESS THAN 50 RDS FIRED. I AM REDUCING INVENTORY OF SAFE QUEENS. $700 NO TRADES. BUYER MUST HAVE TN DRIVERS LICENSE AND/OR TN HCP (PREFFERED). TEXT ME IF INTERESTED.

Vision Kamado grill bundle, BNIB, charcoal or propane, accessories. A couple of years ago I put it the word with friends and family that someone should gift me a komado style grill. Well, I got two of 'em. And me being the irresponsible person that I am, I've been using the other one that is just like this one forgetting that this one was sitting in the way right in the middle of my shop, still strapped to the pallet it arrived on. Oh well, a little late to return it now. So, here it is, up for grabs. Best I can tell, these things retail for about a grand, give or take, depending on accessories. This one needs a new home so it's half price. $500 cash and I'll load it onto your truck or trailer. I'm south of Columbia, between Summertown and Ethridge. Please save me from having to deal with FB marketplace!

I have seen em lock up like that over a single flake of unburnt powder under the ejector star. leroy.

This video is about excessive end shake, but also shows you how to check the gap between the cylinder and the forcing cone. If it's not in spec, you can have a tight gun. The last part shows how to remedy that. It's just a guess on my part, but the possibility is there. Otherwise, my 34-1 has a problem with the ejector rod coming loose and making it hard to open.

Yeah, that's been a minute.

I have a strap on pad that I use with my metal buttplate milsurp bolt guns. It only takes a few rounds through the 8mm for my shoulder to tap out. Can't imagine being in the army back then and banging through a couple bandoliers worth every day. Those guys were tough.

I’m reposting this as a For Trade. I value this at $600 because it’s not a common variant. I’m open to trades for.22 rifles or handguns or 9mm handguns. If I respond with “Thanks, I’ll keep it in mind “ please don’t be offended. I will keep this open for a couple of weeks to see if there’s any interest. Thanks much. I’m north of Nashville.

This. After two shoulder surgeries, hard kicking guns no longer interest me. I probably won't even shoot my trusty Winchester Model 70 .30-06 ever again.

My grandson and I hit a deer on my motorcycle. We had slowed to avoid spooking her, but she ran ahead and darted across our path like she did it on purpose, LOL. Luckily, I was prepared and the only damage was a broken light bracket.

Those are beautiful man!!! awesome work as always!

Safety Reminder for Buyers and Sellers This is an automatic reply meant to protect you as a buyer and a seller on TGO. Use the Buyer/Seller Feedback feature to research who you are dealing with. Please come back and leave feedback for each other after the transaction is complete. Your experience will help others. Never agree to use an electronic form of payment to buy or sell a gun! None of the electronic payment services will protect you against fraud in a firearms transaction. They all have terms of service FORBIDDING the use of their services to buy/sell guns. DON'T DO IT. Be very wary of anyone who insists on brokering a deal in private or outside of TGO. Scammers almost always prefer to operate out of the public eye. The complete Trading Post Rules and also some more helpful suggestions can be found by clicking this link. Everyone should read them at least once! ~~~ This was an automatic reply ~~~

Yes , sorry

I sent you a PM, let me know what you think about it. The link I sent you just go down and hit the HOME and it will take you to the Home page.

Adding a aftermarket compensator is adding another variable to your carry handgun that can effect reliability. They lower slide velocities, can alter timing, and usually require hot ammo to cycle more reliably. This is your carry gun, and reliability is the primary concern. I would just practice and train with the pistol as it is, especially since you just bought it. The P10c is a fine handgun. Put a thousand rounds through it, or get some training if you’re worried about recoil management, and follow up shots. Your probably old enough to remember that until about five minutes ago, the handgun world knew you didn’t need a comp and a red dot to use and shoot a handgun effectively.

Stevens Model 240 This is a prewar over/under 410 Rare wood stock variation According to my research there are less than 15000 ever mfg between the late 30's and early 40's Double triggers, double hammers Fantastic condition Squirrels will scatter when they see you coming More pics available but it really needs to be seen in person $850 Trades would have to be something I want for the collection East Tn but travel/ shipping is an option

No sorry...none planned anytime soon.

1500

In all honesty........if you have issues with recoil, get an accurate gun with less recoil. A super mag in the dirt always gets it's azz handed to it by a 6mm on the target.

14 or 15 total, I think. I'm going to cheat a bit & trailer the bike to a mate's place in Gunnison CO though. That should give me a full 10 days to tour around out there. I'm planning on averaging 300 miles a day & I've got a laundry list of sites I'd like to visit.

Be careful out there, Rob. Me and the old lady missed a deer today by just a hair. I had the back brake locked, and was pulsing on the front brake hard as I could and still not lose control. I’m sure glad I’ve ridden for a long time and wasn’t a newbie. We’d have crashed, and nearly did so anyway. She handled it well.

Someone else beat you to it. Money already in my PayPal account. Sorry bout that.